Accessories

Lynx Distribution System

A modular DC busbar system that connects batteries, inverters and chargers tidily.

Type

Modular DC busbar

Outputs

4 fused outputs

Works with

Lynx Smart BMS

Interfaces & Cables

Interfaces and cables that connect Victron devices to a computer and to a GX device.

Connectivity

VE.Bus · VE.Direct · USB

Works with

MultiPlus · Quattro · MPPT · GX

Type

Interface and cable

Shore Power Cable

• Waterproof Shore Power Cable and Inlet IP56 • Moulded Plug and Connector • Power indication LED • Protection Cap • Stainless Steel Inlet Available in: 15M…

Solar Cable

Solar Cable — Victron Energy cable.

12V cigarette lighter plug

The 12V cigarette lighter plug, with fuse, is an accessory for the Blue Smart IP65 Charger with DC connector.

Clamp connector

The clamp connector with fuse is an accessory for the Blue Smart IP65 Chargers.

2 meter extension cable

The 2 meter extension cable is an accessory of the Blue Smart IP65 Charger with DC connector.

M6/M8 eyelet connector

The M6/M8 eyelet connector with fuse is an accessory for the Blue Smart IP65 Charger with DC connector.

Non inverting remote on-off cable

Use this cable to connect the following products to the VE.Bus BMS: - Skylla-TG all models - Battery Protect models BP40i, BP60i and BP200i (all discontinued).

VE.Direct non inverting remote on/off cable

Use this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models.

VE.Direct to RS232 interface

Connect products with a VE.Direct connection and an RS232 connection with Victron's VE.Direct to RS232 interface.

Ziehl Voltage and Frequency Relay UFR1001E

The UFR1001E monitors voltage and frequency in plants for own generation of electricity.

CANUSB interface

The CANUSB interface is used to connect a VE.Can product to a computer.

RS232 to USB converter

The Victron RS232 to USB Converter connects Victron products with an RS232 port to a device that has a USB inlet, such as a computer or a GX device.

VE.Direct TX digital output cable

The VE.Direct TX digital output cable can be used in combination with the BlueSolar and SmartSolar MPPT chargers. It supports the following applications:

BlueSolar PWM-Pro to USB interface cable

With the BlueSolar PWM-Pro to USB interface cable you can connect the BlueSolar PWM-Pro to your computer.

Inverting remote on-off cable

Use this inverting remote on/off cable to connect Victron inverters and inverter/chargers that require an active pull-down remote signal—including the…

RJ45 UTP Cable

A cable to connect Digital Multi Control, Inverter Control, Interface MK3-USB, VE.Bus connections between multiple VE.Bus devices and to make VE.Bus and…

VE.Can RJ45 terminator

The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB.

VE.Bus to NMEA 2000 interface

This NMEA 2000 drop cable connects a VE.Bus product, for example a Multi or Quattro, to a NMEA 2000 network.

VE.Bus to BMS 12-200 alternator control cable

This cable connects the VE.Bus BMS to the Smart BMS 12/200, enabling the alternator charge control feature of the BMS 12/200 to be used in systems with a…

VE.Can to NMEA 2000 micro-C male cable

Use this cable to connect a Victron product with a VE.Can port to a NMEA 2000 network. More information in the NMEA 2000 & MFD integration guide.

Skylla-i remote on-off cable

Use this cable to connect a Skylla-i to a VE.Bus BMS. The VE.Bus BMS will then disable the Skylla-i charger when the batteries are fully charged.

Fuses & fuse holders

Besides an assortment of ANL, MIDI and MEGA fuses, we feature three different types of fuse holders:

Wall mount enclosure for BMV or MPPT Control

Easily mount a BMV-700 series or MPPT Control on a wall.

Wall mount enclosure for 65 x 120mm GX panels

Wall mount enclosure for 65 x 120mm GX panels.

Zigbee to USB converter & Zigbee to RS485

This pair of Zigbee converters is to wirelessly connect an Energy Meter to a GX Device.

Shunt

Victron shunts are used to accurately measure current in high-power DC systems.These shunts are available in sizes ranging from 500A to 6000A, all with a 50…

VE.Can Power Cable

When the CAN bus is not powered by a Skylla-I or an MPPT, you will need the new VE.Can Power Cable to supply the power.

USB extension cable one side right angle

Some of the USB plugs on our cables are too long to fit in the Wall mount box with a Color Control GX. Use this USB extension cable. Available in 0,3 m length.

VE.Can to CAN-bus BMS cable

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. There are two types, A and B.

MPPT WireBox - Tr

The MPPT WireBox provides an extra level of safety, and is particularly useful if your MPPT Solar Charger is installed in a general access area.

MPPT WireBox - MC4

The MPPT WireBox provides an extra level of safety, and is particularly useful if your MPPT Solar Charger is installed in a general access area.

Battery indicator panel

The battery indicator panel shows the state of charge of the battery. It is an accessory for the Blue Smart IP65 Chargers.

Battery Indicator Eyelet M8

The Battery Indicator Eyelet M8 is an accessory for the Blue Smart IP65 Chargers.

RS485 to USB interface

RS485 to USB interface, available in 1.8 m and 5 m.

M8 circular connector Male/Female 3 pole cable

This cable can be used to extend the BMS communication cables.

Wall Mount for Blue Smart IP65 Charger

This Wall Mount will be especially useful if you like to keep your smart charger handy - above your workshop bench, for example.

Rubber bumper for IP65 Charger

The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too.

CANvu GX IO Extender and wiring kit

CANvu GX IO Extender and wiring kit.

Carry Case for Blue Smart IP65 Chargers and accessories

Smart and professional; this new snap shut carry case provides protective stowage and easy transport for your Blue Smart IP65 charger, and its accessories.

MagCode Power Clip

The Victron MagCode Power Clip is a magnetic 12V connector designed for quick and reliable connections between the Blue Smart IP65 Charger and a vehicle’s…

DIN35 adapter

DIN-Rail adapter to easily mount a device on a DIN-Rail. Suitable for the Cerbo GX.

RJ45-splitter

This splitter is used to connect the MultiPlus 500VA - 1600VA range in parallel and 3 phase configurations, or in other installations where multiple VE.Bus…

Cable for Smart BMS CL 12/100 to MultiPlus

This cable connects between a non VE.Bus BMS (Smart BMS CL 12-100 or smallBMS) and a MultiPlus (MultiPlus, MultiPlus Compact or MultiPlus-II).

MagCode Power Port

MagCode Power Port — Victron Energy accessory.

Orion-Tr DC-DC Charger Isolated remote cable

In the Orion-Tr Isolated DC-DC Chargers the remote on/off circuit is referenced to the primary battery (e.g. starter battery).

GX Touch 50 adapter for CCGX cut-out

This adapter is designed to easily replace the CCGX display with the newer GX Touch.

Busbars

Busbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.

RJ12 UTP Cable

A cable to connect the BMV shunt to the BMV head unit.

GX Touch Wall Mount

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall.

SolidSwitch 104

The SolidSwitch 104 will switch DC loads of up to 70V/4A and can be controlled by a low power digital signal.

Anti-Islanding Box 63A single and three phase

The Anti-Islanding Box 63A single and three phase is a combination of an anti-islanding device, the Ziehl UFR1001E, two in-line contactors and main circuit…

EV Charging Station NS Front

EV Charging Station NS Front — Victron Energy accessory.

Outdoor LTE-M puck antenna

Outdoor LTE-M puck antenna. Length: 3 meters.

Outdoor LTE-M wall-mount antenna

Outdoor LTE-M wall-mount antenna. Length: 5 meters.

GX WiFi module long range (Netgear AC1200)

GX WiFi module long range (Netgear AC1200).

GX Touch Protection Cover

The GX Touch 50 & 70 protection cover prevents damage from UV light during prolonged exposure to the sun.

Pre-Charge Cable

The Pre-charge Cable allows internal capacitors of an inverter, inverter/charger or MPPT to be pre-charged via the DC terminals before connecting the battery.

Ekrano GX Wall Mount

The Ekrano GX Wall Mount accessory enables quick and secure installation on a solid wall.

LiNGST

The Lithium NG Service Tool (LiNGST) allows a direct wired connection between a Windows PC and the M8 service connector on Lithium NG batteries and the BMS NG…